Sign Up For Deals!
EarthX (TM-281) 24V, 5amp, OPTIMATE BATTERY CHARGER/MAINTAINER/POWER SUPPLY
The Optimate TM-281 24V Lithium battery charger will charge and maintain your lithium battery with 5 amps of energy so your battery is ready to go when you are! This lithium charger also has a “tune” or power source mode of delivering 4 continuous amps of energy so you can program your EFIS or retune your car plus a pushbutton activated BMS “wake up” mode to safely wake up a battery out of sleep mode.
- Lithium Battery Charger
- Lithium Battery Maintainer
- Power Supply
- Ultimate LiFePO4 lithium battery charger. High efficiency diagnostic charger and tester for LiFePO4 / LFP batteries.
- Perfect for charging and seasonal maintenance of a 24V LiFePO4 / LFP lithium battery sized from 2 to 100 Amp-hour.
- SAVE : Low Volt Start of 0.5V + 3-step low volt SAVE and TEST; CHARGING AMPS: 5A (AmpMatic).
- IDEAL FOR: Lithium LiFePO4 (LFP) batteries from 2 – 100Ah; INPUT: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed.
- USE: Indoor / Outdoor (lowest temperature: -40°F / -40°C); STYLE: Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector; Weatherproof battery lead & standard battery clip set included.
The new OptiMate lithium charger will protect your investment and guarantee your Lithium Iron Phosphate (LiFePO4 / LFP) battery will perform as advertised for a very long time.
With 5 Amps of charge current available OptiMate lithium battery chargers unique multi step ampmaticTM program recharges and balances cells within the battery quickly and efficiently.
OptiMate lithium’s battery maintenance mode delivers current to the vehicle circuitry, protecting and keeping the battery at 100% charge.
OptiMate lithium battery charger – Battery Performance Guaranteed!
|Item Weight||3.45 pounds|
|Product Dimensions||8.2″ L x 3.1″W x 12.1″H|
How it works
- Pre-qualification test: OptiMate Lithium battery charger displays the condition of the battery before charging and measures environment temperature. The ampmatic™ charge program is selected according to temperature and battery condition.
- Low Volts recovery: The safeTº protection mode controls charging during this sensitive battery SAVE stage, to ensure that an over discharged battery will be correctly and safely recovered. Tests are conducted through-out the SAVE program to determine if the battery has successfully recovered and can advance to BULK CHARGE.
- Bulk charge: the ampmatic™ processor actively adjusts charge current to match battery capacity and condition, achieving a complete charge in the shortest time. Progress is tracked against the ideal charge curve for LiFePO4 batteries.
- Short-circuited / dead cell check: Charge progress is tracked against the ideal LiFePO4 charge curve, internal damage will be detected and unnecessary charging is prevented of a battery that cannot be recovered.
- Absorption and equalization: for 10 minutes the current is delivered in pulses with voltage controlled between 28.0 and28.6V, aiding cell voltage equalization and improving the battery’s overall power delivery.
- Charge verification: the voltage is limited at 27.2V while the ampmaticTM processor monitors the current absorbed by the battery. If this reveals a less than optimal charge, the program reverts to absorption for a further 10 minutes.
- Voltage retention test: is conducted for 30 minutes during which no charge current is delivered, with 5 possible test results indicating the battery’s general state of health. A green (voltage > 25.4V) result extends the test up to 12 hours, to check for excessive self discharge or higher than expected power loss through the vehicle’s electrical system.
- Charge maintenance: The 12 hour MAINTENANCE CHARGE CYCLE consists of 30 minute float charge periods at a voltage of 27.2V followed by and alternating with a 30 minute ‘rest’ (no charge current) periods. During the float charge period current is delivered only if the battery has lost charge due to connected vehicle circuitry. A refresh cycle may be performed if the charge level has dropped significantly. The voltage retention test and maintenance charge cycle will repeat 24 hours after the start of the very first test and continue to repeat for as long as the charger remains connected.
The alternating charge and ‘rest’ maintenance program protects the battery against over discharge by connected vehicle circuitry, making it ideal for indefinite and 100% safe long term maintenance charging.
|Recommended for LiFePO4 / LFP batteries||up to 100Ah|
|Program control||ampmatic™ microprocessor|
|Input current max.||0,55A @ 230V|
|Typical annual energy cost||< €1 (continuous maintenance)|
|Reverse drain current||less than 0,001A|
|Output current (bulk charge)||0,4A – 5,0A|
|Charge time limit||24 hours (maintenance time: unlimited)|
|Maintain / test cycles||30 min/30 min (alternating hourly)|
|Charge retention test||Range: 20.2 – 26.6V. GOOD (green) = battery voltage > 26.6V|
|Size||8.2″ x 3.1″ x 12.1″|
|Mounting||easy direct wall mounting|
|Input cable length||2m|
|Output cable length||2m|
|Included Accessories||SAE-71 fused eyelet set, weather protected
SAE-74 clamps set for bench charging
|Operation temperature range||-40°C / +40°C|
CJD-FFNK-990-BK-Black 990 SMT (G-A4), CJD-FFNK-990-MF MACHINE FINISH 990 SMT (G-A4) – SOLD OUT, CJD-FFNK-990-O ORANGE 990 SMT (G-A4) SOLD OUT, Drop in fuel filter for 690 and 990smt filler – 286148 (R-G4), Upgrade to BLACK Billet Cap (G-E7) CJD-SM-GASCAPK-AL-BK, Upgrade to ORANGE Billet Cap (G-E8) CJD-SM-GASCAPK-AL-O, Upgrade to BLUE Billet Cap (G-D8) CJD-SM-GASCAPK-AL-BL, Replacement black plastic GAS CAP (R-J3) – (736715), 690/990 SMT – CJD FILLER Replacement screws – set of 3 (misc part/ M6x30 (Grey 1), Replacement KTM 690 Tank o-ring – 0770050030 (SB), Replacement vent line fitting (EB50/ (Grey1)